(View map)
- BrandJet
- Country of manufactureUnited States
The Powermax105 system provides excellent cutting of metals up to 32 mm thick. The running cycle of this system and its productivity in industrial processes allow it to cope perfectly with the most difficult tasks on cutting and a metal witness mark.
Seven cutting torches of Duramax of various configuration are included in the package of system. Thanks to it, the system can be used in the wide range of works on manual cutting, automatic cutting in portable option, cutting with use of a coordinate table both robotic cutting and a witness mark.
The Smart Sense™ technology automatically corrects gas pressure depending on the mode of cutting and length of a wire of a cutting torch. It also defines the termination of service life of an electrode, automatically powering off a cutting torch in order to avoid possible damage of other details or preparation.
Technical characteristics
Values of entrance tension | CSA | 200–600 V, 3-f., 50/60 Hz |
CE | 400 V, 3-f., 50/60 Hz 200–400 V, 3-f., 50/60 Hz |
|
CCC | 380 V, 3-f., 50/60 Hz | |
Entrance current at 21,9 kW | 200/208/240/380/400/480/600 IN, 58/56/49/28/25/22 AND | |
Output current | 30–105 And | |
Rated output voltage | 160 In a post. current | |
Running cycle at 40 °C | 80 % at 105 A | |
Idling tension |
|
|
The sizes with handles | 592 mm of; 274 mm Sh; 508 mm In | |
Weight with a cutting torch of 7,6 m |
|
|
Gas source | The clean, dry, fat-free air or nitrogen | |
Recommended stream speed and gas pressure on an entrance |
Cutting: 217 l/min at 5,9 bars Witness mark: 227 l/min at 4,8 bars |
|
Length of the entering power cable | 3 m * | |
Current source type | The inverter — BTIZ (the bipolar transistor with the isolated lock) | |
Requirements to the engine drive | 30 kW for a full conclusion 105 A | |
Certificates | The certificate of CSA allows to use the equipment in North and South America and Asia, except for China. The system has the following certificates: CE, C-Tick (a tick in a letter C), CU/GOST, UKRSEPRO and AAA. These certificates allow to use it in EU countries, Australia, Belarus, Kazakhstan, Russia, Serbia, Ukraine and other countries in which these certificates are applicable. CCC — for use in China. |
|
Guarantee | Guarantee for current sources — 3 years, on cutting torches — 1 year. |
* Some models CCC are delivered without network cable.
Work with use of the engine generator
Rated power of the engine | Output current of system | Productivity (arch stretching) |
30 kW | 105 And | Full |
22,5 kW | 105 And | Limited |
22,5 kW | 85 A | Full |
15 kW | 85 A | Limited |
15 kW | 65 And | Limited |
Production flow chart of cutting
Material | Thickness | Current | Technological speed of cutting * | ||
inches | mm | And | inch/min. | mm/min. | |
Low-carbon steel | 1/4 | 6 | 105 | 192 | 5090 |
3/8 | 8 | 105 | 116 | 3870 | |
1/2 | 12 | 105 | 76 | 2060 | |
3/4 | 20 | 105 | 40 | 940 | |
Stainless steel | 1/4 | 6 | 105 | 224 | 6000 |
3/8 | 8 | 105 | 112 | 4210 | |
1/2 | 12 | 105 | 68 | 1860 | |
3/4 | 20 | 105 | 34 | 810 | |
Aluminum | 1/4 | 6 | 105 | 265 | 7090 |
1/2 | 12 | 105 | 91 | 2450 | |
3/4 | 20 | 105 | 50 | 1190 |
* Values of speeds of industrial cutting are received when testing in laboratory of the Hypertherm company.
Values of speeds of industrial cutting make about 80 % of the maximum values.
For obtaining optimum quality the actual values of speed of cutting can differ depending on features of the carried-out cutting.
Additional information see in the operator guide.
Operational data
Productivity | Thickness | Cutting speed |
Cutting | ||
Recommended | 32 mm | 500 mm/min. |
38 mm | 250 mm/min. | |
Limit (manual cutting) | 50 mm | 125 mm/min. |
Burned * | 22 mm | |
* the Nominal thickness of a prozhig for manual cutting or when using automatic system of adjustment of height of a cutting torch. | ||
Productivity | Metal renting speed | Edge profile |
Witness mark | ||
Typical witness mark | 9,8 kg/h | 6,4 mm () x 7,4 mm (Sh) |